| Carburators, Throttle Bodys, Equipment |
| Dynojet kit stage 1
Intended for motorcycles with a stock engine using the stock airbox, air filter and stock pipe. Stage 1 kits are fully adjustable to allow the use of a well designed aftermarket pipes and stock replacement air filters like K&N. Stage 1 kits are designed to improve throttle response and driveability and in most cases power increases of approximately 5% throughout the entire power range can be achieved. Please indicate model and year of construction.
| Prod.Id 621
119 EUR
|
| Dynojet kit stage 2
Intended for motorcycles with a stock or mildly tuned engine using a well designed aftermarket pipe with a modified airbox and a stock replacement air filter. Stage 2 kits are designed for applications where individual filters cannot be installed and for applications where airbox modification improves the engine's performance. In most cases power increases of approximately 8% can be achieved. PLease indicate model and year of construction.
| Prod.Id 622
119 EUR
|
| Keihin 39 street kit
Flatslide Carburators for maximum performance. Complete kit including all needed mountingparts (Throttle grip, wires, K&N filter racing, airbox cover, 4 mainjets for individuell adjusting, gaskets, a.s.o.). Pre-adjusted. 39mm Steet Kit for Ducati 750-900SS and Monsters, Cagiva Elefant 750-900 and Bimota DB2-Mantra.
Specify model, type, year of construction, firther modifications.
Mounting Instructions
| Prod.Id 631
999 EUR
|
| Keihin 41 street kit
Like item 631 but 41mm diameter.
Please specify model and model year when ordering.
Recommended for Supersport drivers to achieve the maximum top speed.
Mounting Instructions
| Prod.Id 632
1.049 EUR
|
| Airbox adapter for Keihin carburators
CNC milled aluminum adapter to connect the 39 and 41mm Keihin-batterys to the original airbox of the Monster and SS models. Scope of supply contains the o-ring for the carb. Price for one piece. | Prod.Id 632a
59,90 EUR
|
| Electric fuel pump
Applicable for all monster models with diaphragm fuel pump. Used part but 100% o.k. | Prod.Id 632b
89,90 EUR
|
| Re-building Keihin dual carbs to solos
We devide the battery for single use. Please send in. All needed parts for the change are included in the scope of supply. | Prod.Id 632u
395 EUR
|
| Keihin solo kit 39
Keihin Flatslide carbs solo kit including short inlet ducts.
Racing carbs to use with open velocity stacks.
Including mountingkit.
Diameter 39mm
For all Ducati 2Valve engines.
Mounting Instructions
| Prod.Id 640
1.225 EUR
|
| Keihin solo kit 41
Like item 640 but 41mm diameter. Maximum HP and torque raising for race track and sports use.
Mounting Instructions
| Prod.Id 641
1.325 EUR
|
| Throttle control and cables Keihin FCR carb´s
Throttle control with opening and closing cable for Ducati Monster and SS models. Please indicate when ordering. We use the longer Monster cables also at the SS models cause they are a little bit to short.
All parts are also available seperatly.
Throttle control = 29 €
Cables, opening and closing = 69,90 € | Prod.Id 64101
99,90 EUR
|
| MIKUNI TDMR40 Carburetor-Kit for Ducati 900 M up from 1993
The carburetor kit consists of the following components:
Flat slide carburetor battery MIKUNI TDMR40-B14 (Prepared for Ducati 900M with original airbox)
Special throttle grip with wires
Original Choke lever at the steering wheel is maintained
Adapters in front for original rubber
Adapter in the back for original airbox
Fitting instruction/data sheet
TÜV certificate
Main and slow jets (for open air filter covers and K&N filter)
Mounting instruction (German) SS/Monster
| Prod.Id 642
1.055 EUR
|
| MIKUNI TDMR40 Carburetor-Kit for Ducati 900 SS up from 1991
The carburetor kit consists of the following components:
Flat slide carburetor battery MIKUNI TDMR40-B14 (Prepared for Ducati 900 SS with original airbox)
Special throttle grip with wires
Original Choke lever at the steering wheel is maintained
Adapters in front for original rubber
Adapter in the back for original airbox
Fitting instruction/data sheet
TÜV certificate
Main and slow jets (for open air filter covers and K&N filter)
Mounting instruction (German) SS/Monster
| Prod.Id 643
1.055 EUR
|
| Adjustable fuelpressure regulator i.e. models
Special upgrade equipment for injection models for tuning engines. Steplessly adjustable from 1.5 to 5.0 bar.
Mounting instruction
| Prod.Id d423
239 EUR
|
| Fuelpressure regulator 3.0 Bar
Special upgrade equipment for injection models for tuning engines.
The eprom or computer must be adapted afterwards!
| Prod.Id d4231
89,90 EUR
|
| Fuelpressure regulator 4.5 Bar
Special upgrade equipment for injection models for tuning engines.
The eprom or computer must be adapted afterwards!
| Prod.Id d4232
89,90 EUR
|
| Adjustable fuel pressure regulator
Adjustable from 3 to 5 Bar. Fits nearly all models up from model year 1994 such as 748, 916, 996, 998, 749, 999, Sport Classic, and so on.
NOT PRESET ! | Prod.Id d4233
143 EUR
|
| 54mm Throttle Body in exchange
Reworking a 50mm throttle body to 54mm. Inclusive CNC adapter and aluminium velocity stacks .
Please send us your throttle body for reworking. Bolt on kit complete.
| Prod.Id d447
698 EUR
|
| 58mm Throttle Body Testa Stretta -In Exchange
For the models 749/999 S and R types.
Change of the standard throttle body with 54mm to 58mm diameter modified. The 749 models should be equipped with this bigger throttle body only in combination with a capacity extension-big bore kit !. The 999 models increase with this change in the achievement starting from 8000 rpm. With R models the maximum performance rises around approx. 5-6 HP and 7-8 Nm, depending upon used exhaust system.
In the scope of supply the carbon fiber velocity stacks and new nozzle holders are included. Please send us your injection body for modifieing.
The motorcycle needs a new mapping after the installation. Power commander or similar devices are necessary for it.
Delivery time approx. 14 days.
Picture 1
Picture 2
Mounting instructions
Sample diagrams:
Red Curve: 999S original with fine tuning
Blue Curve: same engine with 58mm throttle body
Diagram HP
Diagram Torque
Workshop report: Reconstruction throttle body
| Prod.Id d448
698 EUR
|
| 54mm up to 58 mm throttle body 998 Bi/R- Modification
Throttle body modificationen from 54 mm stock to 58 mm converted .
Now we offer also this conversion,because all customers are fully satified with this power and torque increase and smooth response on throttle !!
we do this with a compromise in case of velocity stacks.We mashine
the velocity stacks to bigger diameter and fit the stock onces again .Therefore price is reduced to 749-999 types.
| Prod.Id d449
598 EUR
|
| Throttle body 50mm 2V 1000/1100/1200
Throttle body with bigger diameter for the use with 1000/1100/1200cc 2 V engines.
These throttle bodys are specially made for Racing/Tuning for the bigger 2 valve engines. The performance enhance approx. 5-7 HP in the level from 115 HP upward! The original cross section is 43mm, so it´s an increase of 7mm to 50mm! You can place the injection body directly on the manifolds. No further modifications required. When ordering, please send us your potentiometer. It will be reused.
This work is a garage job. Expect a delivery time of 14 days.
Throttle body mounted
We use this modified throttle body also in our Ducati 2V Testa Demon.
| Prod.Id d450
945 EUR
|
| Quick throttle grip Ducati Race
Aluminium quick throttle grip incl. wires. Complete CNC Aluminium billet made. This short stroke is really short and mainly for real race conditions manufactured! 3 different gearing plates inside ,from really short opening degree to a smoother acceleration !! you can make your choice !Weight 150 Gramm. Available for all 4 valve Ducatis up from 916-94 !!
Please indicate model and year of construction when ordering.
| Prod.Id d55
199 EUR
|
| Racing throttle grip 749/999 Street Race
CNC milled short stroke high-speed gas grasp particularly for the 749/999 models. The original gas cables can be used.
By the change the angle of rotation to full power is reduced only small, but more important is that the butterfly valves in the first half of the movement opens more slowly so the achievement employment can be proportioned more exactly. The second half of the rotating motion sets then the butterfly valves faster rising to 100%. The butterfly valve position does not rise linear as at the original.
Delivery takes place without any rubber grips. The orignal can be re-used.
Weight 60 gram.
Deail picture
Not suitable for the 1098 models cause it has the same way!
| Prod.Id d56
124,90 EUR
|
